i have a prochem bruin ii and the chemical shows flow on prime but not when i...
I have a bruin ii and when I prime the chemical it shows full flow, also I have an open hose hooked up to a shutoff valve in my extra solution outlet, and when I open that the chemical shows flow, but...
View ArticlePerformer Bear
I have a performer Bear. Yes, I know it's old, but it runs like a scalded dog! When i shut it off and before I open the waste tank discharge drain., the waste water starts running out the front of the...
View ArticleValve on transfer pump
The valve on my tank that transfers the water to the cleaning unit is breaking. Can these tanks be welded ? And what is inside them ? Thanks for any help and have a great afternoon.
View ArticlePressure regulator problem
Pressure regulator on my Prochem Performer doesn't go past 700Psi. Does anyone know how to fix it? I still have plenty of oil in the pressure pump. I can easily change the pressure below 700, pressure...
View ArticleProchem will only run with choke open
Finally have my TM moved over to my new van got everything set up and for some reason my machine will only run with the choke open ? It has been ran very few hours over the last 3 months mainly just...
View ArticlePerformer 405 timing chain
Ok, so my P405 has this ticking & I'm pretty sure it's a loose/broken timing chain tensioner. Now I remember this engine from way back when I was a teenager in my Dat 521 P.U. but man try to find...
View Article03 Prochem Legend se excessive water pressure.
My Prochem Legend SE has excessive pressure. The pressure gage is stuck at 1500psi even with the machine off. If I connect a cleaning wand and start the machine the pressure overcomes the control valve...
View ArticleProchem Blazer Xl heat and vacuum loss... Help please.
Hi all, New guy here, I have a prochem blazer xl with nearly 1000hrs. The problem started a week ago with loss of vacuum and no heat when the machine is running. With the vacuum port's clear and...
View ArticlePutting new resin in a Prochem water softener
I think my water softener has needed new resin for a while. I have never been able to find a cheap, easy way to even tell if I have soft water. My machine doesn't seen to have hardly any scale related...
View ArticleOverheating Water.
Thank u in advance. I have this prochem legend se( older) and the water is overheating causing machine to shut down while I'm not using the water. I clean the filters and orifice.The only thing I...
View ArticleProchem Blazer xl blower and cat pump maintenance.. help.
Hi all, Any advice and recommendation on maintenance and the correct amount of oil in each? Thanks all much appreciated. Sam.
View ArticlePerformer Chemical Pump
What's up everyone? I need some help. I have a Pro Chem Performer first off. About a week ago I noticed that my rinse chemical was being used. This is weird because I JUST spent $1200 on it at the shop...
View ArticleProChem Legend Bogging down under load 900 hours
So my Legend GT has been a great machine. Just recently it started jumping all over the place when a load was put on it. Once we put the hose on it really bogs down. Cleaned all 3 heat exchangers, New...
View ArticleFuel line bypass!
I noticed my prochem legend se - (older )was leaking gas. I don't know the name of this part but under that black circle where the leak was coming from. It's it ok to bypass this fuel line and anyone...
View ArticleKholer Engine replacement
I got a prochem legend that the engine rubber seal popped out. I was cleaning and engine shut off and smoked due to empty oil because of the leak. The tech. said he can replace the seal but it might...
View ArticleProchem Legend Se pulley
I was trying to replace the oil seal for my truckmount and it couldn't take it off. Here is the pictures of it. Thanks for your help. Does it need to come off the top one. I used different tool and it...
View ArticleTemperature gauge stuck
Does anybody know what would cause the temperature gauge to be stuck at a certain temperature, although the real water temperature is much higher? My gauge started acting up last week when it was stuck...
View ArticleProchem Bruin II
I have a problem with my Prochem BRUIN II the machine run with my waste tank automatic float switch disconnect.can someone help me.if the switch not work the machine will just run and water all over...
View ArticleHow often are you forced to replace a fuel pump?
Tomorrow I'm taking my van to mechanic to have the fuel pump replaced. It died right before I was about to pre-spray the carpet. It'll be my 3rd fuel pump in the last 3 years. What a pain..They all...
View Article