Water is only warm inside the water box
The water inside my water box on my truckmount isn't hot. The temperature gauge is about 130f when it's on full trottle. I touched the water inside before they replaced my heat exchanger and it was...
View ArticleProchem chemical pump
Just got the new prochem installed in the van Saturday and it's been wonderful up until this afternoon. I had a 4 hour gap before my last job for today and when I arrived at the house to get started my...
View ArticleLeaks from temperature sensor
Prochem legend se. I noticed today, there's a leak coming from the temperature sensor every 10 seconds. Anybody has this problem before? thank u
View Articlefuel leak
Hi, I noticed today a little of fuel sipping out the side of the carburetor where the throttle/butterfly rod is? Is there some seal that could be replaced? Any suggestions will be appreciated. Thanks
View ArticleSapphire 870 oil filter
Hello folks! This is my first post so please bare with me. I need some advice on an oil filter for my SS 870 truck mount. The current one is a EFL 600 and it's on a 1.6 l ford engine. The engine is...
View ArticlePerformer 405 Carb.
Does anyone know exactly what make and model the carburetor on the Performer 405's Nissan A12 motor is? $500+ for a new one and I'm looking for options. Aaron
View ArticleVery strong gas
Truckmount gas was very strong today ran for a while then shut off .Sprayed carb cleaner in it stop smelling strong for a minute then later it shut down what could be the problem Sent from my Nexus 7...
View ArticleProchem preheater issue
When I bought my Prochem Performer Bear, I had to have my preheater bypassed because of water pouring out of the vacuum exhaust. Now TM doesn't want produce more than 180 degrees F, so at the wand it's...
View ArticleProchem Legend chemical pump problem
The chem pump is not feeding chemical. It keeps filling with air. I have two valves coming off the truck mount; one for my solution line and another for mixing chems and rinsing stuff. When I prime the...
View ArticleProchem Legend Heat
Got a prochem legend and the other day I came out side to get a spray bottle and noticed the temperature had dropped to like 180*or so. I let it sit for a few minutes and the heat went back to 230* or...
View Articlechanged check valve . now not gettin pressure ....
had freeze . popped plug out . replaced bolt and flange that recieves plug/ check valve. no leaks no pressure .lost new 2 year owner. b with knowledged person tomarrow investigating problem. any tips...
View ArticleProchem Blazer help again
Blazer ran for 2hr today after that shuts off now only runs for 5 to 10 minutes and shuts off even after it cools down Sent from my Nexus 7 using TMF Forums mobile app
View ArticleVideo of truckmount shutting off less than 10min
Sent from my SCH-I545 using TMF Forums mobile app
View ArticleNeed New Kohler engine for Prochem Legend
I was told that the replacement engine is for my original 8 thousand hour 90's engine is the new 20 HP Prochem model #40-902152. I just hope this is the correct one. I was quoted 3200 by Jon Don and...
View Articlechemical pump leak
when I turn my chemical on it leaks, the brass elbow seems to be tight that is connected to my line going to flowmeter and that's were I have my leak is by elbow. any thoughts?
View Articlepump out question/locked up?
my waste tank float switch went bad. I bypassed switch to see if I had any other problems. been bad for almost a year and haven't used pumpout. so in process of bypassing to get juice to pump out all I...
View ArticleGrease
Found grease on the floor of my van today cannot figure out where it's coming from but it's really sticky I got some of it up before I sent the picture but made you guys can figure it out. Sent from my...
View Articlepumpout switch question
as earlier posted my pumpout switch is bad, do I need the whole switch assembly or just the switch magnet housing? don't want to buy what I don't need, thanks again guys!
View Article